ESC Flip PRO Computer Keyboard Stand for Desk, Adjustable Tilting Keyboard Lifter for Ergonomic Typing, Minimalist Keyboard Riser with Non-Slip Feet, Extendable Holder Fits Most Keyboards

As titled; this product is perfect. I purchased a couple of them, use them almost daily / very heavily (well, I use the keyboards they're attached to) and ZERO issues. They have remained firmly adhered to the bottom of my keyboards, and they are far more ergonomic than the absolutely diabolical and objectively harmful top to bottom tilt that most all keyboards come with.You are NOT supposed to have your keyboard higher at the top (FN keys) than at the bottom (space bar, wrist rest)This causes you to bend your wrists backward, and THAT is very hamful & contributes mightily to carpal tunnel & all sorts of other related issues.Your keyboard is SUPPOSED to be higher at the wrist rest, and lower (flat on your desk) at the top; where the FN keys are.Anyway; this device is beautiful & should come standard with all keyboards.Buy one for every keyboard you have!

This product really did the trick. It was extremely easy to install. It only takes a few seconds. If you want to raise the back end of your keyboard, this is a very convenient and effective product. You can choose from three heights. Very sturdy. You can't go wrong.

I bought this because I had lost both legs on my wireless keyboard. I’ve had it a couple of months and haven’t even removed the piece of paper to help it adhere to the surface of my desk. Even with the paper on it, it works fine. Since it’s so light weight, it’s made it really easy to use my keyboard when I use my laptop outside of my office, as long as there’s a hard surface, mainly my coffee table or dining room table. I’ll just prop my keyboard on top of it, which is usually enough slant that I don’t have to use the risers. The risers are easy to use and snap into position for stability. I can’t rate the strength of the adhesion since I haven’t needed to remove the protective paper yet, but am assuming it will match the high quality that the overall product seems to be.

These days, most keyboards, including even expensive ones like my Logitech mechanical, have absolutely minimal rear legs. This results in a totally inadequate angle for comfortable typing, for me.In the past, I used to use a block of wood that I'd duct-tape to the underside. This works way better and has many height adjustment options. I'm currently using the 2nd lowest setting, which is enough, but I could tilt the keyboard way higher if I wanted. So far the adhesive has been holding pretty well, and this is after using the stand for a couple months now.My only criticism is it's kind of on the expensive side, but on the other hand, quality doesn't come cheap.

Excellent product

Between working from home a few days a week and using my home desktop for general use, I get a lot of keyboard time in on nearly a daily basis. Nearly every keyboard I've owned has had either one or both of its stand legs break off at some point in time. I was looking for a stand / riser to address that issue, and by extension to provide some comfort and relief on my wrists. This fit the bill perfectly.This stand attaches to the back of the device you want to use it on with suction pads on both ends of it. These pads help keep the stand in place. So far, I've found they allow the stand to stick well to the back of the keyboard. I can move the keyboard around on my desk without the stand coming off, but I did apply some pressure when applying the stand to the keyboard.The stand is adjustable width-wise, so it can be used on other devices besides keyboards like tablets. I haven't had this stand for too long at this point, so I don't know how it would affect the adhesiveness of the pads over time if it's often being switched out between different devices.There are four different rise levels. The levels are adjusted by the riser legs. All you need to do is pull out the appropriate leg for the height you want. So far I've only used the lowest leg, but it works perfect for me in conjunction with a wrist rest to provide typing comfort throughout the course of the day.

I got the newest magic keyboard to go with my Mac, to my surprise it does not have any type of adjustment. It lays almost completely flat making it hard to type on comfortably. With this stand being able to adjust to different heights I can now type on my magic keyboard without issue.Another great thing I love about this stand is that you can remove and adjust as you need without the sticky part causing an issue.

I have to say I am surprised by all of the favorable ratings for this product. Based on those ratings, I thought I would try it out and purchased it. I have tried several other similar items that were actually lower quality but worked better and for less money!This one did not stick for a day! And, I am not going to put super glue on my expensive keyboard to make it stick! The keyboard has a perfectly flat surface, clean, and still, this keyboard stand would not stick past a few seconds. It would start sliding and then slide right off the keyboard!And, for the few seconds that it was on there, there was not enough lift to the keyboard. I had purchased it for that lift, and there wasn't any, really. So, why bother with it, especially for the price?!As far as being lightweight... Well, I guess it was lightweight, but I am not sure that that would be a benefit as it did not work. So, I gave it a three as far as lightweight, but again, that really isn't one of the items I would have used to rate it. It simply is not worth it for the purpose I purchased, to raise the keyboard, and it doesn't stay on the keyboard anyway, so I tossed it in the trash, which is equal to tossing $25 in the trash.